the information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. this documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. it is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. neither schneider electric industries sas nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein. jun 7, 2013 1 product data sheet characteristics ATV71HC20N4D variable speed drive atv71 - 200kw - 300hp - 480 v - emc filer main range of product altivar 71 product or component type variable speed drive product specific appli- cation complex, high-power machines assembly style with heat sink component name atv71 variant reinforced version without dc choke emc filter integrated network number of phases 3 phases [us] rated supply volt- age 380...480 v - 15...10 % motor power kw 200 kw 3 phases 380...480 v motor power hp 300 hp 3 phases 380...480 v line current 286 a 480 v 3 phases 200 kw 300 hp 357 a 380 v 3 phases 200 kw 300 hp apparent power 235 kva 380 v 3 phases 200 kw 300 hp prospective line isc 50 ka 3 phases nominal output current 387 a 2.5 khz 380 v 3 phases 200 kw 300 hp 387 a 2.5 khz 460 v 3 phases 200 kw 300 hp maximum transient cur- rent 580 a 60 s 3 phases 200 kw 300 hp 638 a 2 s 3 phases 200 kw 300 hp speed drive output fre- quency 0...500 hz nominal switching fre- quency 2.5 khz switching frequency 2.5...8 khz adjustable 2.5...8 khz with derating factor asynchronous motor control profile ena (energy adaptation) system for unbalanced loads flux vector control (fvc) with sensor (current vec- tor) sensorless flux vector control (sfvc) (voltage or current vector) voltage/frequency ratio (2 or 5 points) type of polarization no impedance modbus complementary product destination asynchronous motors synchronous motors supply voltage limits 323...528 v supply frequency 50...60 hz - 5...5 % network frequency limits 47,5...63 hz speed range 1...100 asynchronous motor in open-loop mode, without speed feedback 1...1000 asynchronous motor in closed-loop mode with encoder feedback 1...50 synchronous motor in open-loop mode, without speed feedback speed accuracy +/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 tn to tn +/- 10 % of nominal slip without speed feedback 0.2 tn to tn torque accuracy +/- 15 % in open-loop mode, without speed feedback +/- 5 % in closed-loop mode with encoder feedback http://www..net/ datasheet pdf - http://www..net/
2 transient overtorque 170 % +/- 10 % 60 s 220 % +/- 10 % 2 s braking torque 30 % without braking resistor < 150 % with braking or hoist resistor synchronous motor control profile vector control without speed feedback regulation loop adjustable pi regulator motor slip compensation adjustable automatic whatever the load not available in voltage/frequency ratio (2 or 5 points) suppressable local signalling 1 led red drive voltage output voltage <= power supply voltage insulation electrical between power and control type of cable iec cable without mounting kit 1 45 c copper 70 c pvc iec cable with an ip21 or an ip31 kit 3 40 c copper 70 c pvc iec cable without mounting kit 1 45 c copper 90 c xlpe/epr ul 508 cable with a nema type1 kit 3 40 c copper 75 c pvc electrical connection terminal 2.5 mm2 awg 14 ai1-/ai1+, ai2, ao1, r1a, r1b, r1c, r2a, r2b, li1...li6, pwr terminal 4 x 185 mm2 l1/r, l2/s, l3/t, u/t1, v/t2, w/t3 terminal 4 x 185 mm2 pc/-, po, pa/+ tightening torque 0,6 n.m ai1-/ai1+, ai2, ao1, r1a, r1b, r1c, r2a, r2b, li1...li6, pwr 41 n.m 360 lb.in l1/r, l2/s, l3/t, u/t1, v/t2, w/t3 41 n.m 360 lb.in pc/-, po, pa/+ supply internal supply 24 v dc 21...27 v 200 ma overload and short-circuit protection internal supply for reference potentiometer (1 to 10 kohm) 10.5 v dc +/- 5 % 10 ma overload and short-circuit protection analogue input number 2 analogue input type bipolar differential voltage ai1-/al1+ +/- 10 v dc 24 v max 11 bits + sign software-configurable current ai2 0...20 ma 242 ohm 11 bits software-configurable voltage ai2 0...10 v dc 24 v max 30000 ohm 11 bits sampling duration 2 ms +/- 0.5 ms li1...li5 discrete 2 ms +/- 0.5 ms li6 if configured as logic input discrete 2 ms +/- 0.5 ms ai1-/al1+ analog 2 ms +/- 0.5 ms al2 analog response time 2 ms +/- 0.5 ms ao1 analog 7 ms +/- 0.5 ms r1a, r1b, r1c discrete 7 ms +/- 0.5 ms r2a, r2b discrete <= 100 ms in sto (safe torque off) accuracy +/- 0.6 % ai1-/al1+ for a temperature variation 60 c +/- 0.6 % ai2 for a temperature variation 60 c +/- 1 % ao1 for a temperature variation 60 c linearity error +/- 0.15 % of maximum value ai1-/al1+, ai2 +/- 0.2 % ao1 analogue output number 1 analogue output type software-configurable current ao1 0...20 ma 500 ohm 10 bits software-configurable logic output ao1 10 v 20 ma software-configurable voltage ao1 0...10 v dc 470 ohm 10 bits discrete output number 2 discrete output type configurable relay logic r1a, r1b, r1c no/nc 100000 cycles configurable relay logic r2a, r2b no 100000 cycles minimum switching current 3 ma 24 v dc configurable relay logic maximum switching current 2 a 250 v ac inductive cos phi = 0.4 l/r = 7 ms r1, r2 2 a 30 v dc inductive cos phi = 0.4 l/r = 7 ms r1, r2 5 a 250 v ac resistive cos phi = 1 l/r = 0 ms r1, r2 5 a 30 v dc resistive cos phi = 1 l/r = 0 ms r1, r2 discrete input number 7 discrete input type programmable li1...li5 24 v dc level 1 plc 3500 ohm safety input pwr 24 v dc 1500 ohm switch-configurable li6 24 v dc level 1 plc 3500 ohm switch-configurable ptc probe li6 0...6 1500 ohm discrete input logic negative logic (sink) li6 if configured as logic input > 16 v < 10 v negative logic (sink) li1...li5 > 16 v < 10 v positive logic (source) li6 if configured as logic input < 5 v > 11 v positive logic (source) li1...li5 < 5 v > 11 v pwr < 2 v > 17 v http://www..net/ datasheet pdf - http://www..net/
3 acceleration and deceleration ramps s, u or customized automatic adaptation of ramp if braking capacity exceeded, by using resistor linear adjustable separately from 0.01 to 9000 s braking to standstill by dc injection protection type against exceeding limit speed drive against input phase loss drive break on the control circuit drive input phase breaks drive line supply overvoltage drive line supply undervoltage drive motor phase break motor overcurrent between output phases and earth drive overheating protection drive overvoltages on the dc bus drive power removal motor short-circuit between motor phases drive thermal protection drive thermal protection motor insulation resistance > 1 mohm 500 v dc for 1 minute to earth frequency resolution 0.024/50 hz analog input 0.1 hz display unit communication port protocol canopen modbus type of connector 1 rj45 modbus on front face 1 rj45 modbus on terminal male sub-d 9 on rj45 canopen physical interface 2-wire rs 485 modbus transmission frame rtu modbus transmission rate 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 mbps canopen 4800 bps, 9600 bps, 19200 bps, 38.4 kbps modbus on terminal 9600 bps, 19200 bps modbus on front face data format 8 bits, 1 stop, even parity modbus on front face 8 bits, odd even or no configurable parity modbus on terminal number of addresses 1...127 canopen 1...247 modbus method of access slave canopen marking ce operating position vertical +/- 10 degree product weight 140 kg option card i/o extension card communication card modbus tcp communication card fipio communication card modbus/uni-telway communication card modbus plus communication card ethernet/ip communication card devicenet communication card profibus dp communication card profibus dp v1 communication card interbus-s communication card cc-link controller inside programmable card interface card for encoder overhead crane card http://www..net/ datasheet pdf - http://www..net/
4 environment noise level 77 db 86/188/eec dielectric strength 3535 v dc between earth and power terminals 5092 v dc between control and power terminals electromagnetic compatibility 1.2/50 s - 8/20 s surge immunity test level 3 iec 61000-4-5 conducted radio-frequency immunity test level 3 iec 61000-4-6 electrical fast transient/burst immunity test level 4 iec 61000-4-4 electrostatic discharge immunity test level 3 iec 61000-4-2 radiated radio-frequency electromagnetic field immunity test level 3 iec 61000-4-3 voltage dips and interruptions immunity test iec 61000-4-11 standards en/iec 61800-3 en/iec 61800-5-1 en 55011 class a group 2 en 61800-3 environments 1 category c3 en 61800-3 environments 2 category c3 iec 60721-3-3 class 3c2 ul type 1 product certifications c-tick csa gost nom 117 ul pollution degree 2 en/iec 61800-5-1 3 ul 840 ip degree of protection ip00 en/iec 60529 ip00 en/iec 61800-5-1 ip30 on side parts en/iec 61800-5-1 ip30 on the front panel en/iec 60529 ip30 on the front panel en/iec 61800-5-1 ip30 on side parts en/iec 60529 ip41 on upper part en/iec 61800-5-1 ip41 on upper part en/iec 60529 ip54 on lower part en/iec 61800-5-1 ip54 on lower part en/iec 60529 vibration resistance 0.6 gn 10...200 hz en/iec 60068-2-6 1.5 mm peak to peak 3...10 hz en/iec 60068-2-6 shock resistance 4 gn 11 ms en/iec 60068-2-27 relative humidity 5...95 % without condensation iec 60068-2-3 5...95 % without dripping water iec 60068-2-3 ambient air temperature for operation -10...50 c without derating ambient air temperature for storage -25...70 c operating altitude 1000...3000 m with current derating 1 % per 100 m 1000 m without derating rohs eur conformity date 4q2009 rohs eur status will be compliant http://www..net/ datasheet pdf - http://www..net/
|
